|
Home InventoryBall
Mills Continuous
BALL
MILLS CONTINUOUS
PHOTO
AVAIL |
INVENTORY
NUMBER |
BRIEF
DESCRIPTION |
 |
PC2240 |
Rod Mill, Hardinge, 6' Dia. x 12' Long, Steel Lining, with Liners, 200 HP Elliott Motor, 440 Volt, with Falk gearbox, approx. weight 61,000 lbs. |
|
PC2241 |
Ball Mill, Hardinge, Tricone, Continuous, Quant. Available: 2) 9' Dia. x 6' x 8', Lined, Solid all Steel Shell, detachable bolted trunnions, equipped with single scoop feeders, discharge has internal cone grate with slots, 200 HP Elliott Motor, 440 Volt, 1765 RPM, 235 AMP, 3 Phase, 60 Cycle, coupled to Falk gearbox. |
|
PC2242 |
Rod Mill, Marcy, 6' Dia. x 12' Long, Steel Lining, 200 HP Elliott Motor, 440 Volt. |
|
PC2609 |
Ball Mill, Hardinge, 10' Dia. x 84" Conical Granite Lined, air swept continuous design, direct herringbone pinion and bull gear drive with gear reducer and 250 HP motor drive, 40" self aligning bearings, 6' diameter fan driven by 250 HP motor, Raymond Mechanical Air Separator with 200 HP motor drive, approx. 10' diameter x 34" straight side, 12' conical bottom, approx. 10' diameter x 15'6" high primary cyclone and two approx. 6' diameter x 15'6" high secondary cyclones, Martin Lubricating system for mill bearings, mill relined in 1998 and in excellent condition, fully welded construction, new bearings installed in 1989, along with new Voith Turbo Coupling, main drive motor installed new in 1995. |
|
PC10202 |
Ball Mill, Denver, 4' x 6', Complete with Trunnion Bearing Housing, Bull Gear and Pinion, V-Belt 50 HP Drive Motor, Chute Feed and Trunnion Overflow. Unit has 17 tooth pinion jack shaft with 5' diameter drive shieve, 100 teeth on bull gear, 8" wide.
|
|
PC11930 |
Sag Mill, Hardinge, 6' x 24", Includes Factory Support Structure, 25 HP Motor, 480 Volt, Gear Reducer, Chain Driven, Steel Liners Grate Discharge, Chute Fed, Good Condition. |
|
PC12037 |
Kobe-Allis Ball Mill, 9' x 15' Long (2745mm Diameter x 4570mm Long) Regrind Mills with Yasakawa 45- KW Synchronous Motors, 3300 Volt, 60 cycle (less motor) Capacity rated 35 metric tons per hour. |
|
PC12038 |
Allis Chalmers Ball Mill,3082mm (10') D x 5486mm (18') L, overflow type. Gear and Pinion driven through 3-7 ratio speed reducer FORMERLY Driven By Westinghouse 597 Kw (800 hp) electric motor, 4000 Volts, 3 phase, 60-cycle, 890 rpm. (No Longer Included) FORMERLY used a (2) Lube Oil High Pressure Lubrillo System Pumps, Model PF - 2006 - 2334, gear type, single stage driven by 2.2 kw (3 hp) electric motor, 220/440 Volts, 3 phase, 60-cycle, 855 rpm. (No Longer Included) Includes overflow sump, trunion bearings, feed spout controls and other standard accessories. |
|
PC12042 |
Hardinge Continuous Tri-Cone Ball Mills, (Quant. Available: 2) 14' Diamger x 16' Long, Grate Discharge Set up for Dry Grinding, Complete with Motors and Drives, 1250 HP, Steel Lined, Mill turns 16 RPM, equipped with Lubrication System. |
|
PC12080 |
Denver Ball Mill, Continuous, 3' Dia. x 5' Long, Complete with 20 HP, 3 Phase, 60 Hz, 220/440 Volt, Electric Motor through gear reducer, pinion and two piece ring gear, accessories include air/electric auto lubrication system with barrel pump, feed and discharge chutes, liners appear to be in good condition, unit is mounted on I-beam frame, no ball charge or electric starter. |
|
PC12037 |
Kobe-Allis Ball Mill, 9' x 15' Long (2745mm Diameter x 4570mm Long) Regrind Mills with Yasakawa 45- KW Synchronous Motors, 3300 Volt, 60 cycle (less motor) Capacity rated 35 metric tons per hour. |
|
PC12038 |
Allis Chalmers Ball Mill, 10' Dia. x 18' Long (3082mm Dia. x 5486mm Long), 597 KW. |
|
